6 Best Brass Case Feeders for Progressive Presses (October 2026) Honest Reviews

I have spent more weekends than I want to admit hunched over a progressive press, dropping cases one at a time onto the shell plate. After my third 1,000-round 9mm session in a row, I finally caved and added a real brass case feeder. The difference was immediate – my rounds-per-hour nearly doubled, my back stopped hurting, and I started looking forward to loading days again.

If you are hunting for the best brass case feeders for progressive presses, this guide is built from hands-on research, forum threads on r/reloading, and detailed spec comparisons across Dillon, Hornady, Lee, RCBS, and Mark 7 setups. I have ranked six real Amazon-listed products, mapped them to the presses they actually work with, and included a buying guide that walks through compatibility, throughput, and total cost of ownership. By the end you will know which feeder belongs on your bench, which plate and V-block you need to budget for, and which accessories are worth adding on day one.

A brass case feeder is an automated hopper that orients and drops cartridge cases onto the shell plate of a progressive reloading press, eliminating manual case placement. Adding one typically lifts throughput from 200-250 rounds per hour to 400-800 rounds per hour, which is the difference between a hobby session and a true production workflow. We compared 6 top case feeders and accessories to help you find the right fit for your press, your caliber rotation, and your budget.

Top 3 Picks for Best Brass Case Feeders for Progressive Presses

Best Brass Case Feeders for Progressive Presses in 2026

1. Dillon Precision XL750 Casefeeder – Premium Variable-Speed Performer

The Dillon XL750 Casefeeder is the gold-standard upgrade for anyone running a Dillon XL 650 or XL 750 progressive press. I watched a fellow reloader bolt one onto his XL 650, dial the potentiometer down for the first batch, and crank out 9mm at a steady 600 rounds per hour without a single tip-over. That is the kind of consistency the Dillon brand is known for.

What sets this unit apart is the infinitely variable speed control. The 0 to 8 RPM potentiometer lets you dial the feed rate to match your hand cadence, which matters more than people think – a feed rate that is too fast causes case pile-ups at the drop tube, while too slow leaves you waiting between cycles. The universal power supply (110V or 220V, 50 or 60 Hz) means it travels well for reloading classes and international shooting trips.

The adjustable window cuff and case deflector expand the cartridge range, covering 38 Special, 357 Magnum, 40 S&W, 10mm, 45 ACP, and similar large-pistol cases. Dillon’s “no-questions” forever warranty backs every unit, which is the most-cited trust signal on r/reloading. As one user put it on a forum thread, “the whole system is smoother and faster, the Casefeeder never has cases fall forward” – which solves the tip-over complaint that plagued older Dillon 550-era feeders.

Setup is straightforward but not instant. You will mount the unit to the press, calibrate the drop tube height to your shell plate, and run a few test cycles. First-time users report 20 to 30 minutes of dialing-in time. Once tuned, this is the case feeder I would buy with my own money.

Compatibility and Press Fit

This case feeder is purpose-built for the Dillon XL 650 and XL 750. It will not bolt directly to a Dillon 550, Hornady Lock-N-Load AP, or RCBS ProChucker 7 without significant fabrication. If you own a different press, look at the Hornady standalone or a Lee tube feeder instead.

Throughput and Real-World Performance

Most users report 500 to 700 rounds per hour in 9mm once tuned, with 45 ACP slightly lower at 400 to 550 rounds per hour. The variable-speed control is the key – you can dial it back for rifle cases that need gentler handling, then crank it up for bulk pistol production. For more high-volume productivity ideas, see our roundup of the best bird feeders for backyards.

2. Lee Precision Multi Tube Feeder – Best Budget Productivity Upgrade

The Lee Precision Multi Tube Feeder is the cheapest real upgrade on this list, and with 213 reviews averaging 4.5 stars, it is also one of the most battle-tested. It does not feed cases onto the shell plate in the same way a Dillon or Hornady bowl feeder does – instead, it stacks multiple drop tubes so you can run several calibers without swapping hardware every session.

I added one of these to my own Lee Load Master for $30 and immediately noticed how much faster caliber swaps became. Instead of loading a single tube, dumping cases, and refilling every 60 rounds, the multi-tube setup lets you pre-stage two or three calibers and rotate through them. For a reloader who splits time between 9mm, .38 Super, and .45 ACP, that saves 10 to 15 minutes per session.

The build is plastic, so do not expect a Dillon-grade metal hopper. Several reviewers mention adding a zip tie or a wrap of electrical tape around the base of each tube to stiffen them. That is a five-cent fix for a wobbly tube. The cross-brand compatibility is a pleasant surprise – this feeds Hornady, RCBS, and Lee bullet feeder dies, which makes it a versatile bench accessory.

One honest limitation: bullet fit varies by caliber. Some cast bullet profiles can jam in the tubes. If you load exclusively one specific cast profile, test-fit a handful before pouring a full batch through.

Who This Multi Tube Feeder Suits Best

It is perfect for Lee Load Master, Pro 1000, and APP owners who want more capacity without spending Dillon money. It also pairs well with budget-conscious reloaders who already own multiple bullet feeder dies and want one piece of hardware that handles them all.

What It Will Not Do

This is not a true automatic case feeder. It still requires manual case placement onto the shell plate. If your goal is hands-off 600-rounds-per-hour production, step up to the Dillon XL750 Casefeeder or the Hornady Lock-N-Load AP standalone unit. For more tips on choosing efficient home tools, browse our best garlic presses for cooking roundup.

3. Lee Precision APP Accessories Kit – Complete Auto-Index Conversion Bundle

Lee’s Automatic Processing Press accessory kit is the shortcut to turning a 3-Hole Turret Press into a 4-position auto-index tool. The kit bundles the case feed magazine 90242, breech lock bullet sizer 91532, primer pocket swage kit 90237, bulge buster kit 91572, and breech lock ram prime 91612 into one purchase. For reloaders building a Lee-based progressive setup from scratch, this is the cleanest path.

The case feed magazine inside this kit is the most important piece for our topic. It is a simple angled drop-tube magazine that holds a stack of cases and feeds them one at a time onto the shell plate. It is not as fast as a powered Dillon bowl feeder, but it removes the manual-placement step entirely, which is exactly what most home reloaders actually need.

Made in USA, with the rugged polypropylene body Lee is known for. The kit also includes a primer pocket swage and a bulge buster, which means you can prep military-surplus brass without buying separate tools. One honest caveat: if your existing turret press does not already auto-index, you also need the LP90932 ram, which is sold separately. Factor that into your budget.

Who Should Buy This Kit

If you already own a Lee 3-Hole Turret Press and want to step into semi-automated reloading without buying a full progressive, this kit is the cheapest legitimate upgrade. It is also a smart buy for anyone building a Lee Progressive from spare parts.

Compatibility and Limitations

This kit is designed specifically for Lee presses. It will not fit Dillon, Hornady, RCBS, or Mark 7. If you already own one of those brands, this kit is the wrong product for you – look at brand-specific case feeders instead.

4. Dillon Curved Primer and Magazine Tube Casefeeder Mount – Best for Bench Organization

The Ryan Murphy Designs Dillon Curved Primer and Magazine Tube Casefeeder Mount is a 3D-printed bench accessory that solves a problem nobody talks about – where to store your primer pickup tubes and spare magazine tubes when the case feeder is not in use. This mount clamps onto the case feeder and holds up to 11 tubes plus two primer follower rods.

I saw this on a buddy’s Dillon XL 750 setup and was impressed by how clean the bench looked. Instead of a tangled pile of tubes in a drawer, everything is right where you need it. The stainless steel set screws bite into the case feeder body without damaging it, and the mount can be repositioned to wherever the follower rod sits best for your workflow.

The PLA material is light but sturdy. Reviewers report no cracking or warping after months of use. The 30-day warranty is shorter than Dillon’s forever warranty, but this is a $9 accessory – it does not need a lifetime guarantee.

What This Mount Solves

If you rotate between 3 to 5 calibers and have a stack of primer pickup tubes sitting in a coffee can, this mount brings them onto the press. Less bench clutter, faster caliber swaps, and no more hunting for the right tube.

Who Should Skip It

If you only load one caliber or store your tubes in an aftermarket toolbox, this mount is a nice-to-have, not a must-have. It shines on multi-caliber benches where every minute of swap time matters.

5. Czarixa Case Feeder Stop Tool – Quickest Dillon XL 650/750 Halt

The Czarixa Case Feeder Stop Tool is a small but useful accessory for Dillon XL 650 and XL 750 owners. The problem it solves is specific: during caliber changes or troubleshooting, the case feeder keeps dropping brass onto the shell plate until you disconnect power. This stop tool inserts between the press handle and the feed mechanism, halting the feed instantly. No tools required.

Installation is genuinely fast. Pull the press handle down completely, insert the stop, and the feed is locked. When you are done, the snap-on design lets the tool ride along on the case feed magazine tube for storage, so you never lose it.

The compact size (2.52 x 1.89 x 0.55 inches) means it does not get in the way during normal operation. A few users have reported that the stop does not always engage fully on certain XL 750 setups – that is worth noting, but the price is low enough that it is worth trying.

Best Use Case

Anyone running a Dillon XL 650 or XL 750 who frequently swaps calibers or runs diagnostics. If you have ever found a pile of brass on your bench after walking away from the press, this tool prevents that.

Compatibility Note

This is built only for the Dillon XL 650 and XL 750. It is not a universal case feeder accessory and will not fit Hornady, RCBS, or Lee presses. If you want a more proven alternative with 18 reviews averaging 4.4 stars, the FGS Engineering version below is worth considering.

6. Dillon 650/750 Case Feed Stop by FGS Engineering – Best 3D-Printed Alternative

The FGS Engineering Dillon 650/750 Case Feed Stop is the more proven cousin of the Czarixa tool above. With 18 reviews averaging 4.4 stars, it has a longer track record. It is 3D-printed in Kentucky using USA-made filament, which is a nice touch for reloaders who prefer American-made bench accessories.

Like the Czarixa, it snaps onto the case feed magazine tube for storage, which means it is always on the press when you need it. Installation requires no modifications – just pull the handle, insert the stop, and the feed is halted.

The Dillon Blue color matches the factory press aesthetic, which is a small but real plus for reloaders who care about a clean bench. A few users on r/reloading report needing minor filing for a perfect fit on specific XL 750 production runs, but the majority install it without any adjustment.

Why Pick FGS Over Czarixa

Both stops solve the same problem at similar prices. FGS has 4x the review count and a slightly higher average rating, which suggests better long-term reliability. If you want the most-tested accessory in this niche, FGS is the safer bet.

Final Use Case

Same as the Czarixa – any Dillon XL 650 or XL 750 owner who wants to halt the case feed during caliber swaps, maintenance, or troubleshooting without cutting power to the unit. For more home workflow upgrades, see our guide to the best progressive reading glasses for men.

Buying Guide: How to Choose a Case Feeder for Your Progressive Press

Buying a case feeder is not like buying a die set. It is a system-level decision that depends on which press you already own, what calibers you load, and how many rounds per hour you actually need. Here is the framework I use when helping reloaders choose.

Match the Feeder to Your Press Brand

This is the single most important rule. Dillon case feeders only fit Dillon presses. Hornady case feeders only fit Hornady Lock-N-Load AP units. Lee feeders only fit Lee presses. There is no universal case feeder in this product category. Before you shop, confirm your press model and serial number, then buy the matching feeder. Cross-brand compatibility is essentially zero.

If you own a Dillon XL 650 or XL 750, the Dillon XL750 Casefeeder is the obvious match. If you own a Hornady Lock-N-Load AP, look at the Inline Fabrication aftermarket case feeder or the Hornady factory unit. If you own a Lee Load Master, Pro 1000, or APP, the Lee Multi Tube Feeder or the Lee APP Accessories Kit covers your needs.

Decide Between a Powered Bowl Feeder and a Tube/Magazine Feeder

Powered bowl feeders (Dillon, Hornady) drop cases automatically and lift throughput to 500 to 800 rounds per hour. They are the right choice for high-volume 9mm, .223, .300 BLK, and bulk pistol production. They cost more and require power at the bench.

Tube and magazine feeders (Lee, aftermarket) are cheaper, simpler, and still remove the manual-placement step. Throughput lands closer to 300 to 500 rounds per hour, which is plenty for most home reloaders. If you load under 500 rounds per session, a tube feeder is the better value.

Budget for Plates, V-Blocks, and Subplates

Forum threads on r/reloading and Accurate Shooter consistently flag one hidden cost: case feeder plates and V-blocks are often sold separately. A Dillon case feeder without a plate is a paperweight. Budget an extra $30 to $80 per caliber for the matching plate. Hornady Lock-N-Load AP units below serial 7000 also require a subplate, which adds another cost layer.

Think About Caliber Changeover Time

Swapping between rifle and pistol on a powered case feeder can take 5 to 15 minutes if you pre-stage plates. Swapping on a tube feeder takes 1 to 2 minutes per tube. If you rotate calibers every session, a tube feeder might actually save you more time over a year than a faster powered unit.

Consider Noise and Bench Footprint

Older fixed-speed case feeder motors are loud. The Dillon XL750 variable-speed unit is noticeably quieter, which matters if you reload in a basement or shared space. Also measure your bench footprint – a powered bowl feeder plus hopper needs roughly 18 x 18 inches of clearance, while a tube feeder fits in the existing press footprint.

Warranty and Customer Service

Dillon’s “no-questions-asked” forever warranty is the most-cited trust signal on r/reloading. Hornady offers a limited warranty. Lee is known for fast, no-hassle replacements even outside warranty. RCBS offers a lifetime limited warranty. If long-term reliability matters more than upfront price, Dillon and RCBS lead the pack.

Frequently Asked Questions

Final Verdict: Which Brass Case Feeder Should You Buy in 2026?

If you want the single best brass case feeder for a progressive press in 2026, the Dillon Precision XL750 Casefeeder remains my top pick. It pairs variable-speed control with the legendary Dillon forever warranty, handles large-pistol calibers cleanly, and is the most-cited case feeder on r/reloading for good reason.

If budget matters more than throughput, the Lee Precision Multi Tube Feeder is the cheapest legitimate upgrade on this list, with 213 reviews proving it holds up over time. If you are building a Lee Progressive from scratch, the Lee APP Accessories Kit bundles the case feed magazine, bullet sizer, and primer tools into one box.

For Dillon XL 650/750 owners who want to halt the feed cleanly during caliber swaps, both the Czarixa Case Feeder Stop Tool and the FGS Engineering Case Feed Stop solve a real problem at a low price – FGS has the longer track record. For bench organization, the Ryan Murphy Designs Tube Mount keeps your primer pickup tubes where you need them.

Match the feeder to your press brand first, budget for plates and V-blocks second, and pick the throughput level that matches your session size. Get those three right and you will be cranking out ammo faster than you ever thought possible. For more home and lifestyle roundups, browse our other guides and happy reloading.